If you want to get a simple and expert opinion on wiring a ceiling fan with light with one switch, you must follow our article below. Because in this article our expert team has built on a real job.
However, an experienced electrician should do electronic technical work as there is some risk in every electrical work.
But we hope you can gain enough experience about wiring a ceiling fan with light with one switch if you follow the given article adequately.
Wiring a ceiling fan with light with one switch
Table of Contents
How to install a wiring a ceiling fan with light with one switch which takes a single space to control both fans speed and fanlight. This scenario assumes that there is only one switch controlling the fixture will also run. Through a few common variations if you have a black wire coming from the switch as opposed to a black screw post. We’ll also look at a variation where you may be working with two individual sets of wires that are coming down, for example.
Are you replacing the ceiling fan and a double switch that controls the lighting of the ceiling fan before you do an electrical job?
Be sure to cut all power to the fixture and the electrical box by turning off and flipping the breaker of some tools you want to have on hand. I like to have a slot screwdriver Philips a red and green handle, Robertson.
Some pliers also are wire cutters, some wire strippers flashlights, electrical tape, and some wire nuts or Moretz. Now starting with your line in which is your live wire, your power source. The weight from your line in is going to go to the white of your load-out, which is the one going to the fixture. You’re bare the copper wire, which is your grounds, will be connected together along with the green from the switch.
If your switch doesn’t have an existing green, then make a pigtail and put that pigtail on as well. It should be a ground coming from your junction box, which made me in the form of a pigtail as well. So all those coppers will be connected the switch itself may vary on the specifics of what they designate for light and what they designate for fans in our case.
The switch has designated red for light yellow for fan; double-check your instructions for that make sure that you’re specific to your switch. So here I’m going to take my red light, and in my three-wire, my red happens to be the one that is going to my light in the fan.
So those will connect those together, and then I’ve got my yellow fan wire that they’ve specified from the switch. And now we’ll go to my wife, which I have going to my fan motor again that could vary for your setup. You have to know what is connecting on the other side, so I’ve got red going to my fan light in my scenario. I’ve got black going to my fan motor.
So again here light to the light motor to motor, so that leaves us just with our black from our line in and this is the hog wire that’s giving us our electricity. So that is going to be connected to the screw post on the switch. So when we have all our connections together, we can see we’ve got our white coming from our line in our power source to our white of our load out to our fixture, our black or hot wire going to the black screw post.
We’ve got all our grounds together, and there should be a ground connecting to the electrical box. They’ll all be one there in our scenario, and I specified for this switch our red light going to the wire that I have to my light fixture and then the yellow fan order going to the wire. I have to my fan Lord again these two could vary on your setup, and you need to know which goes to the light and the motor. Now let’s take a look at a bit of variation, so now our first variation, I have another switch here which controls.
The ceiling fan speed the switch on the side, and then the light just doesn’t on/off with no dimmer. Now this one doesn’t have the same screw post that the other one had; it’s got a black wire instead, so all of our other connections will be exactly the same except that this black wire will now go to the line in hot so I’ll wire it up all up.
And you’ll have a look; one thing to note for this switch is the color of the wires is specifying as different from the other one. So this switch, the yellow goes to light, and the red goes to fan motor, so again, check the specifics of your switch. And the particulars of your ceiling wiring, which one goes to light and which one goes to the fan motor.
So now, with this wired up, we see our black line in our hot wire to our black from our switch our whites together. Our grounds together, and again there’ll be another ground from the junction box; they’re all connected together here. I’ve got my designated light wire going to the light of my ceiling fan setup. And I’ve got my designated red wire going to my designated motor ceiling fan motor wire.
So it could be that you had a double switch in your wall that you’re replacing that controlled the ceiling fan, and you’ve got two sets of two-wire. So there again, you want to be sure you know which one is for the motor which one is for the light; one thing that I find helpful is when you know which is which before you disconnect everything. If possible or immediately after disconnecting, just put a little label on it. For example, let’s say this is our light, and then I’m going to remember that. And then scenario this is our fan motor that makes it a little easier to keep straight.
So if that’s the case, the only thing that we’re going to need to do here is everything’s going to be hooked up like before except that we’ve got an extra white to white and an additional ground to gang together. So in that scenario where we have to separate two wires coming from the fan and light again. Depending on our switch itself, we’ve got our black hotline going to our screw post or our black wire.
We’ve got all of our whites together, so we’ve got the white of our line-in, and each white of our load out connect Together. We’ve got our grounds together with green wire from the switch our bare coppers from the three sets of wires. And we’ll have another one, a pigtail from the electrical box all connected together. We’ve got our light switch designated light wire to our light. Now we’ve got our switch designated fan motor wire to our motor. When you’ve got everything hooked up, it’s a good idea to remove any of these papers, okay.
So here’s our fan switch the controls our fan motor speed and our light; our single switch our line in is coming from the top here. We’ve got our black going to our black screw post; we’ve got our light; this is for our light the load out. This is for our fan motor, the load out, and all of our whites alright gang together here; we’ve got multiple switches happening so much; gang your whites together, and then all of the grounds are gang together here and ground it off to the box. When the work is all done, you’ve got your face plate on turn your breaker.
People also ask:
Can lights and fan on same switch?
Yes, you Can lights and fan on the same switch. Even both fan and lights are running through a switch, and there is additional pressure on the top of the switch. As a result, the switch overheats due to overloading, which poses a hidden danger. If there is a need to connect the lights and a switch, an electrician must do the work.
Since running the fan and lights through the same switch can lead to overload, there is often a risk of the switch burning or catching fire due to a short circuit.
Therefore, if there is a need to operate the fan and light with the same switch, an electrician must be installed and conduct the activities by taking advice.
How do I wire a light and fan to one switch?
You want to know how do you wire a light and fan to one switch. We have written an article about this above. Following is a discussion on how to easily install lights and fans with a switch.
This article is one of the most accepted by a skilled electrician from his own practical experience. Because we present each of our technical writings or articles in the form of posts based on the work of an electrician. However, using a 20 amp circuit breaker creates the possibility of getting rid of some hidden danger.
So we can say, of course, by following the post above you can easily install the fan and lights through a switch.
Can I wire a ceiling fan with 14 2 wire?
Yes, you can wire a ceiling fan with 14 2 wires.
But at present, every manufacturer has to add a light kit to each ceiling fan, which requires additional power flow. As a result, if you use a ceiling fan with a light kit with 14 2 wires, there is a possibility of overload due to excess current.
This can lead to short circuits. So can use 14 3 wires to use lights with a ceiling fan.
how to wire a ceiling fan with 3 wires?
Conclusion
We hope you will be able to gather enough information by following the article on wiring a ceiling fan with light with one switch provided by our expert team. You can also follow our other article 3 speed ceiling fan switch wiring diagram, which provides information about switch wiring.
On the other hand, it discusses how much it costs to install a ceiling fan and How to change ceiling fan light bulb, which, if followed, you will get enough information about the cost of installing a ceiling fan. You should follow this article because if you do not have enough experience, you should get the job done by an experienced electrician. Hopefully, you will get enough information about its cost.
We recommend that if you do not have sufficient experience in this regard, complete the work through an experienced electrician because there is a risk of hidden dangers if there is not enough experience in electrical electronics.