Home Pulp

How to Replace a Light with a Ceiling Fan – Best Guidelines 2021

Our expert team has provided feedback from an authentic and practical experience on how to Replace a Light with a Ceiling Fan so that you will be able to get a complete idea about it through adequate follow-up.

However, if you do not have sufficient experience in this regard, we recommend you have the work done by an electrician. But on the other hand, we hope we will have a realistic experience if we follow these guidelines.

Since the article has been created with expert opinion, hopefully, you will be able to do this without any kind of accident and any hidden danger. Below is the complete guideline on How to Replace a Light with a Ceiling Fan.

How to Replace a Light with a Ceiling Fan
Our expert team has provided feedback from an authentic and practical experience on how to Replace a Light with a Ceiling Fan.

How to Replace a Light with a Ceiling Fan

How to Replace a Light with a Ceiling Fan? I’m going to show you how to change this light into a ceiling fan. The first thing we need to do is turn off the circuit breaker, make sure there’s no power up here. I recommend you have an electrical tester as well to be sure the power is off. We found the master bedroom; you’re going to turn this off. The light turned off when we switched off the circuit breaker.

Alright, so we need to take our light fixture off. Depending on the institution, there are different ways to take these down. This one has a part that unscrews from the bottom. Usually, you can’t see any screws, so there’s a trick somewhere, like, in this case, unscrewing a little ball. Be careful not to drop our glass. We got our light bulbs; I’m going to remove these light bulbs so that we don’t run into problems as we take this off.

I don’t want to accidentally break these, especially those which contain a little bit of mercury. I’m finding a couple of screws up here; we will loosen those enough to get this fixture down. We don’t need to take these screws all the way out at the point.

Okay, I could pry this down a little bit, get my fingers under it, and now I can slide it. Oh, look at this. These screws were not the original screws that came with this fixture. Typically, you can leave the screws in place and undo the entire fixture. However, these screws are too big. Now take the screws out.

How to Replace a Light with a Ceiling Fan
how to replace a light with a ceiling fan

Okay, with the screws out, you want to make sure your electricity is turned off here, so we’re going to use a bit electrical tester to show that. I don’t have it here with me now, but you hold it up, turn it on, and lights will flash if there’s power. I will link to Amazon if you need to pick one of those up, super handy. Once we have turned the powers off, we will unscrew these wires, the wire nuts.

We got our black wire, our hot wire, our white wire, our neutral wire, and the copper wire, our grounding wire. Once these are undone, we’ll be able to get the whole light fixture down. Okay, with that, we got the cables undone, the light fixture comes down.

Alright, next, we’re going to find the mounting bracket. This is one of the most important parts. We need to be sure this fan is supported correctly up on the ceiling. There are multiple ways to secure it like there are some after-market products like this one, which is a ceiling fan with a side mount bracket, or there’s this one that’s a ceiling fan with a support brace kit. This pretty little box says it includes a surface mount support, so we’ll look for it and figure out the best one for this job.

Alright, the easiest installation will be this bracket that was provided that is a surface mount, goes around the box like so. However, the key with this is that you must ensure that both sides of the bracket screw into a stud, so there’s a support beam running somewhere along here. We’re going to try and find it. A couple of ways to do that are to knock and try and guess where it is, use a hammer. I got a stud finder; we’re going to try using that to find locations.

Having a textured ceiling is not helping much with the little pads on this thing. The stud finder was having quite a bit of trouble with the texture on the ceiling. I think some of the wood is being set back a little bit from the ceiling.

For example, there’s a stud right there, and this thing’s not picking it up. Here’s another trick I used, I took my screwdriver, came around the edges of this box, again being sure my power is turned off until I found where the wood was, and I could. From poking around here, I can find that there’s one of the support beams, one of the trusses overhead is running right there.

So with that information, I grabbed the support provided and take a look at my holes, and to line up with the stud, it would have to sit like that. That is not ideal with this box location because when I cover it, half of the box over here isn’t covered, so I’d have the junction box. It’s not above the fan, definitely a problem. We will have to use an old retrofit box, so I’ll show you how to do that. It would be this one that we’re going to put in place.

Alright, we’re installing a Hunter brand ceiling fan today. The process and procedures can be a little bit different for other fans, but the general concepts will be there. We’ve got to remove a set screw like this one, and then we need to work this guy onto our wire, and we got a lot of wires here to work with. This probably got three feet of wire here, which is great if hanging a long way from the ceiling.

Since we’re not going to be hanging so far down the ceiling, I’m just going to give myself about a foot’s worth of wire, plenty to work with. Let me cut the rest off. These guys all get threaded through. This is the little down rod that’s going to be hanging from the ceiling. You want to tighten, screw this down ’til it stops. We were still going ever so slightly. Okay, we got it stopped.

We’ve got to put this set screw back in, and as I put this set screw in, I’m going to use some pliers to help or a square head bit and get it started. Now, this is an important little screw ‘cuz it’s holding this so that the fan doesn’t spin itself off over time, or it gets way loose. Here we go, let’s get this thing tightened in. Alright, I think we about got it. Alright, we’ve got to put this little decorative canopy cover on, slip everything through, and that’s just going to sit there.

How to Replace a Light with a Ceiling Fan
how to replace a light with a ceiling fan

Now, remember this bracket, this bracket here, the one that because we were positioning the support beam overhead, we couldn’t just screw directly to it? Well, this is still essential because it’s going to hold the fan like so, it’s going to sit there. We’ve got to get this thing secured onto our box up in the ceiling.

One thing I forgot to do, I need to remove all these brackets here with these screws. (electric screwdriver whirling) I want not to lose any of these screws. (electric screwdriver whirling) Okay, so our box is going to go on like so. Hopefully, these screws that were provided are long enough for me. This is an important point here, making sure the screws are sufficiently long. If the ones in your box are not long enough, you may have to buy some extra ones. Alright, we got some longer screws now.

We’re going to get this bracket put up in place. Alright, got longer screws; I’m putting the bracket in place now. This bracket has some pads that go to the ceiling. Push into the drywall a little bit, don’t want to over-tighten it. Alright, now we’re putting the entire fan up. We want to be careful we’re not lifting with the wires, lift from the holder up here, or from the bottom, again being careful of wiring. You know it’s in place; it’ll be sitting hanging.

Alright, so you can see how it’s sitting there in the bracket. We’ve got to do some wiring now, get the wires that we need. First, we’re going to connect the ground wires. Currently, there are three ground wires. We’ve got one that comes from the mounting bracket right here, green with yellow stripe, one that comes from the ceiling fan, green with yellow stripe, and one that comes from the home wiring that’s just a bare copper wire.

We’re going to get the ends of our ground wire all exposed. I got my three grounds, putting them into the orange wire nut, going to twist this thing around. Once it feels right, I will give these a tug and see if they all stay in. Alright, they do seem to be staying. We got one wire down. We’ve got to use our wire stripper here, expose the ends of these wires.

The remote control, this particular fan has a remote we’ll be connecting, and this remote, when all is said and done, will be sitting inside everything like this. But until then, I’m gonna keep it out so we can work with stuff. Connecting the yellow and the black wires, the black wire from the fan itself, the yellow wire from the remote control. We’re going to use one of these orange wire nuts.

Yellow and black going together, screw it nice and tight, give them some tug, everything stays. Then we connect the blue wire from the fan and the blue wire from the remote control; that one is easy. Blue wire from the fan, blue wire from the remote control. Okay, now from the remote receiver, connect the black wire to the black wire from the ceiling, remember this is our hot wire. This is a really easy flute device for testing for live wires.

(alarm tone) I turned this one on, see it lights up, so if I touch that one right now, I’m going to get shocked. The other wires don’t have power in it, but it doesn’t even have to touch this one. (alarm tone) Right there, about a centimeter away. This is a great tool. (alarm tone) I don’t know if you can tell, but it’s not (alarm tone). It’s not actually touching the wire, and that lets you know it’s live.

I’m going to go turn that power off again, and with the power off, we know we’re okay to touch it. Okay, I got the receiver; I will connect the black wire from the receiver to the black or hot wire from the ceiling. I’m going to connect the white wire from the receiver, the neutral, the white wire from the fan. And the white wire coming from the house, or the ceiling, all together.

Now anytime you’re working with electrical stuff, know what you’re doing, don’t electrocute yourself, make sure you’re not going to start a fire, follow the local electrical codes. If you’re uncertain what you need to be doing, you probably shouldn’t be doing it, ‘cuz you don’t want to be causing yourself some bigger problems. Alright, the wires are all in there securely.

Now from the receiver, I still have a remote signal wire that’s loose. You can tell that that doesn’t have anything on end, and we’re going to tuck all these wires up in the box. I’m getting them all pushed up into the ceiling box. There. Now we’re going to put this cover in place, and there are two screws, one on each side, loosely put it in to start.

We’ll tighten that down, and now that we’ve got this tightened down, we’re going to check that the fan’s functioning before we get much further, in case we need to double-check any wiring here. Alright, this next step, we’ve got to put the fan blades together. This takes a little time, so it’s a great one to have a helper to care of while everything else is being installed overhead. In this particular fan, we’ve got some grommets that have to go in.

And on the backside, we’ve got to pull them out. Once we have those through, we’re going to put this bracket on, line up our holes, and we screw them in place. There you have it. Now put the ceiling blades on. Alright, now we try to tighten these down. Alright, as we finish up our five fan blades here, now we’re gonna make sure they’re all tight and work on the light.

Now we’ve got to put this and put housing on the bottom here that requires putting some screws in. Now we’re going to feed the wire through this assembly and then finish screwing it down. We’ve got to secure the whole assembly we’re putting up. We need to put the wires in place now, put them together. They color-coded it to make it easy.

Now it’s in place, make sure the wires all go up inside, and then work this housing on. Twist in place, we put the third screw in and tighten all three of them down. Now they’ve provided some bulbs. These are different size sockets than most typical light bulbs. It looks like they’re not LED; it’d be nice to have some LED ones that’ll last for the next 15 or 20 years.

Maybe pick some of those up; it’ll pay for themselves pretty quick in energy savings alone. And we’re going to put the assembly on the bottom. Before I put the housing back on, let’s check and make sure this thing is working. So there we go, lights turn on, and this fan has a.

It can rotate in both directions, so I believe in the winter, you want the fan pushing air up, and in the summer, you want it pushing down, I believe. I’m going to reverse the direction. Let’s try it the other way, and there it goes. I think we’re ready to put the housing on. Put the glass on the bottom.

I’ve got to take that off, there are a few pieces that go together, a somewhat plastic protective one right at the bottom, then this metal one, and then it secures all together. There you have it, everyone. We’ve installed the ceiling fan; it’s not too tough, but it takes a little bit of time and some basic tools, and now it’s working to keep things cool.

Hope you have a good idea about How to Replace a Light with a Ceiling Fan and feel free to contact us if you have any comments or questions.

How to Replace a Light with a Ceiling Fan

People also ask:

Can you replace a light fixture with a ceiling fan?

Yes, you can replace a light fixture with a ceiling fan. Usually, you need to gather some experience and information before completing the task.

To replace a light feature ceiling fan, you must first ensure no electrical disconnection with the fan. Since connecting the light feature to the ceiling fan, must remove the central mounting nut and screws. You can then get the light feature screwed in place by connecting the wires to the electrical power as before.

You can also get an idea of ​​how to change ceiling fan light bulb by following the article published by our research team.

Do you need an electrician to replace a ceiling fan?

Usually, if you don’t have any previous experience replacing a ceiling fan, then you definitely need an electrician to replace a ceiling fan.

Replacing a ceiling fan certainly requires a skilled electrician as there is a risk of hidden hazards in every electrical work. So you must arrange to have your ceiling fan replaced by an electrician. This is because some electrical wiring is required to replace each ceiling fan. It is recommended to go through an electrician. An electrician can solve your problem according to your needs by providing adequate guidelines for replacing the ceiling fan and Wiring.

In addition to this, we have another article Wiring a ceiling fan with light with one switch which by following enough you can get enough information and experience about it. Without an electrician will help you perform your work.

Can an electrician fix a ceiling fan?

When replacing your ceiling fan, be sure to have an electrician do the work because an electrician must handle the work safely. This is because an electrician can safely and reliably repair your fan correctly and arrange for replacement at a reliable location.

If there are any errors or problems with your phone, it discusses how to fix the problem by providing you with reliable information, which you can use to install it in a dedicated place.

Are ceiling fans outdated?

Modern ceiling fans made in the present era play a role in enhancing the beauty of your interior room. A unique and contemporary ceiling fan can undoubtedly improve the beauty of your room and provide adequate air and lighting.

Although based on the use of ceiling fans expressing ideas about your interests among guests. Who comes to your home? Ceiling fans have been used for every homeroom for decades. And are expected to last much longer due to its modern changes. Ceiling fans play an important role in creating a pleasant environment and cool weather in your room.

And it can be installed in a small space so much less space is used in your room. Therefore, according to experts, ceiling fans are still at the top of people’s list of choices, and a decorative ceiling fan is still not out of style.

Conclusion

We hope to know a complete idea and informative discussion about How to Replace a Light with a Ceiling Fan from the above discussion.

The above article is framed as a guideline from a practical work which we hope you will be able to achieve an authentic discussion without any kind of mistake.

Also, if you have any comments or suggestions about How to Replace a Light with a Ceiling Fan, you must contact us, and we will try to answer any questions as soon as possible.

Leave a Comment