Home Pulp

Can you add a downrod to any ceiling fan – Best Guidelines 2021

Can you add a downrod to any ceiling fan? An informative discussion on the subject itself has been presented, which, if followed, will hopefully enable a downrod to collect information on how to add it to any ceiling fan. However, the matter is technical, so it must be done by an experienced technician unless there is information and qualifications on the subject.

But on the other hand, we hope that if you do not have enough information and experience on this subject, you can follow this article to collect from here the things to keep in mind to adjust in a downrod ceiling fan. In addition to this, some other general topics have been discussed, which will help you provide complete information about the downrod of the ceiling fan.

Below you can add a downrod to any ceiling fan.

Can you add a downrod to any ceiling fan?
can you add a downrod to any ceiling fan

Can you add a downrod to any ceiling fan?

Can you add a downrod to any ceiling fan? Today we will see How do you install a ceiling fan extension rod. So I’m going to tell you how that mounts onto it just in case you don’t already know. Before mounting this bracket on your ceiling, make sure that your box is rated for a ceiling fan. You don’t want to install it on one that’s only designed for light because that could come down. And you know you don’t want your fan to fall; let’s get started.

So this fan came with this little, I think it’s three-inch downrod. So how you transfer these parts over to the extension is first you remove this screw. and once that screw is removed this It comes out all right. I’ve transferred the pieces over, so it’s just this plastic collar and this grounding strap. A screw holds on to it, and once you have the plastic piece over. You can put the pin through the holes, and then you make sure that the grooves line up all right.

And then now we put the set screw back in all right. The set screw will hold this assembly in place if you’re wondering if you needed any extra wire on this fan and probably other hunter fans. It’ll come with about 69 inches of wire. So for the three-foot down rod, that is more than enough. So the next thing I’m going to do is mount this bracket up onto the box up there; my ceiling is 16 feet. So I needed to use this 14-foot ladder.

can you add a downrod to any ceiling fan?
can you add a downrod to any ceiling fan

The way that this bracket holds is you get your motor mounted on there. This is a threaded end secured by the set screw, and there’s also a red thread locker. So this end goes in here hangs like that; oh before I move on with the installation. I’m going to give you an overview of what came with it, so this is a wi-fi model, so that’s cool. It has this QR code on top of the fan that you can scan. It’s also on the manual, so some of the other pieces that came with are the screws that hold the blade on some wire nuts balancing kit.

This cover goes on top of the bracket, and it comes with a remote as well; your remote can control various functions, and the blades come in a nice silver or wood. And it came with some led bulbs too these are 800 lumens. I’ll probably put some 100-watt equivalents into it. With motor, you mount this plate onto it, and then the light goes inside of that, and then the light cover goes on top of that. Wow, 14 feet looks interesting up here. I’m going to use these screws that have the star nut.

That’ll prevent them from backing out on their own, and as always, before you work on anything electrical, make sure. You have the power shut off. You don’t want to shock yourself or electrocute yourself and again, make sure that the box is rated for a ceiling fan. You don’t want to mount it on one that’s rated for only a light. Because it may not be strong enough to hold a ceiling fan.

Okay, so here we have the bracket installed on the box on the ceiling. I also wanted to show you these wire nuts that I like to use; they’re called lever nuts by Hueco. And it’s as simple as putting the wire in and just flipping this lever; they’re so much easier to use than regular wire nuts, and the clear ones let you see if the wire is in all the way. And at first, I wasn’t sure if I could trust these, but then on youtube, I found a video of someone running a current test through these.

I could not believe how much current you can run through these before showing a problem. So I use these for everything now; they’re so much easier to use, and you don’t have to worry about twisting. Your wires are all up, and it provides a very secure connection. So with that hunter fan, that specific model only needs one power connection. So I’ve put a lever nut on here to keep it from touching anything else. And then we’re just going to use the hot neutral and the ground.

I just wanted to tell you how I got the wires through the pole. I tried to push them in, but they would keep getting stuck in the middle. So I ended up using the stick, and I taped the wires to its end. And that made it easy to get it in; this is a rod from blinds once we get the wires pulled out from the other end. We’ll thread this rod in here and then tighten the set screw. I just decided to check the manual to see if I needed to align the hole on the downrod with the set screw.

And it does not say anything about that. It just says remove the set screw, install the down rod cut the wires at eight inches, and then tighten the set screw with pliers and not by hand. But when I checked that, I also noticed that they want you to use these two washers to install the bracket. So that’s part of this kit; these two are optional for installing the ceiling bracket.

If your box doesn’t have the machine screws, that’s what those are for, so we won’t use them in this installation. But I’m going to go ahead and remove the nuts and put these washers in okay. I have put the washers on the screws here. I just tightened the set screw, and I decided to go ahead and line up that hole on the downrod with the set screw, so the set screw is into the hole right. Now so there is no way this rod will turn the set screw has been tightened with pliers.

I’ve just trimmed the wires to about eight inches, and you can trim it to about the same length as this ground wire that’s coming out of here. Because that’s about eight inches long, I made them all the same length, and the next step is to strip the wires of their insulation.

And if you have a tool like this, it would make it a lot easier all you have to do is just put it up inside here, and then it’s stripped. So for this installation, we will be installing it using the single switch method, so the blue wire coming out of the fan isn’t used.

So will cap it. So now that I have the downrod attached, I can take it, and we’ll go up the ladder and hang it on the bracket. Okay, so once you’ve gone up to your bracket, all you have to do let’s just put it in; that’s it. I forgot to put this on the downrod before I put it up there. So I’m going to take it back down and slip the cover over, so the cover just slips over all of that. And now that I have it on there, I can put this back up here.

And once you have all the wires neatly tucked away, you can put the cover on, and it’s held on by these two screws, one on this side. And one on the other so for installing the blades. We’ll be using these screws and washers, okay, so that’s what the fan looks like with the blades installed; next, we’ll install this piece using three of these screws, alright. So those screws go right here.

Next, we’ll install the light using the remaining three screws, and before you mount it, make sure you connect the wires. There are two of them, and they just snap together. Now that the light kit is installed, we can go ahead and mount the cover. So the cover just goes on, and you twist it to lock it in place, and when you turn the cover, make sure you hold this.

Because if you only turn the cover, it’s held on only by that rod in the very inside, and you might risk turning it, loosening something, or twisting something. So make sure you hold this part while you turn the glass cover. This 14-foot ladder was the perfect height for this 16-foot ceiling. All right, I’ve finished the final part of the installation. I put the switch in have it turned on turn the power back on.

This May Also Interest You: How to measure ceiling fan size?

can you add a downrod to any ceiling fan?

Ceiling fan downrod guide

ceiling fan downrod guide
ceiling fan downrod guide

Do you know what size download you need for your fan? Okay, let’s look at it together. This download chart helps us determine what download size your fan needs to be based on the ceiling height. For a ceiling below 8 feet, we offer a flush mount or clamp fan. It’s a fan without a download. This will keep the blades 7 feet away from the ground.

And in most states, the blades need to be at least seven feet away from the floor for coding. On an 8 foot roof, the standard pole is a 3, 4-inch download that comes with the fan. This will keep the blade at least 7 feet away from the ground. We also offer standard downloads on 9-foot ceilings.

However, some manufacturers will include a 6-inch download. If your fan Including a 6-inch download, we offer a 9-foot ceiling. 12 Inch Download This download is suitable for 10-foot ceilings. For an 11-foot ceiling, For 18-inch downward, it will keep your blades about 8 feet off the ground; this 24 inch is suitable for an about 12-foot ceiling.

Similarly, in a 13-foot ceiling, we offer a 36-inch download. And for a 14-foot ceiling, we offer a 48-inch download, and for both of these. Your blades are 9 feet away from the ground. More sizes are available for this higher ceiling if you are overwhelmed by all the information.

Ceiling fan downrod guide

Why do ceiling fans hum?

A ceiling-fan hum is usually due to the parts of the fan. Humming is often caused by various problems with the ceiling fan motor. A ceiling-fan hum mainly depends on all the parts of a fan. This noise can often be caused by excessive dirt trapped between the wide blades of the ceiling fan and by excessive pressure on the motor. There are different types of ceiling fan sounds such as:

  • ceiling fan making a grinding noise
  • ceiling fan making a clicking noise
  • ceiling fan bearing noise
  • ceiling fan making a scraping noise
  • The fan makes noise when rotating
  • ceiling fan capacitor hum
  • ceiling fan capacitor noise and
  • ceiling fan humming not spinning

With adequate maintenance, every sound can be removed from a ceiling fan, although each sound questions the effectiveness of a ceiling fan. Regular maintenance significantly reduces the noise of a ceiling fan, and solving these problems increases the efficiency of a ceiling fan.

People also ask:

Do all Downrods fit all ceiling fans?

Whether Downrods used in ceiling fans are universal? At present, ceiling fan companies manufacture the downrods used in the ceiling fans in a specific location. As a result, these downrods can be used in other ceiling fans in addition to a specific one. But some companies have taken steps to use their products with certain brands, so many times they cannot be used with all brands.

How do I put a longer downrod on a ceiling fan?

Ceiling fans currently in use use a specific downrod. But on the other hand, when your ceiling high is too high, you have to add a longer downrod to the ceiling fan. To use a long downrod, you must collect from the local market. Also, looking for all of the local hardware can undoubtedly collect a long downrod. Also, various e-commerce sites provide these services through online shopping, which you can collect through an online payment.

Can you adjust the height of a ceiling fan?

Yes, of course, you can adjust the height of a ceiling fan. Using a downrod, you can use the ceiling fan to adjust to your ceiling height. If your ceiling high is too high or too low, you can address the height of the ceiling fan using a customized downrod. According to national safety standards, the distance from the floor to the floor of a ceiling fan should be 7 feet. So you can use a customized downrod to adjust a ceiling fan accordingly.

Can you put a ceiling fan on an 8 foot ceiling?

Since, according to national safety standards, the distance from the floor to the floor of a ceiling fan must be at least 7 feet, a ceiling fan must be installed keeping this in mind. But many times, the installation of a normal ceiling fan is hampered due to the extra low ceiling of the room. It is impossible to use a ceiling fan with a downrod when your ceiling is 8 feet high. So you need to use a ceiling fan or flush mounted ceiling fan without a downrod.

Conclusion

Can you add a downrod to any ceiling fan? Hopefully, from our above article, you will gather an informative discussion on how a downrod can be attached to any ceiling fan. However, we have discussed other topics besides this topic in this article, which will give you a complete idea about downrod.

Also, our expert team has discussed what size ceiling fan downrod I need and Are ceiling fan downrods universal can be followed to collect complete information about ceiling fan downrod.

Since these jobs are technical, if you do not have enough experience, you must have the job done by an experienced electrician. However, if you follow all these articles, you will be able to gather complete information about the ceiling fan downrod and gain experience.

Related Articles:

Leave a Comment